Produse pentru la colorat (4)

Syntech Pavicrom PU Two-component aliphatic polyurethane coating, resistant to UV rays, coloured, in a vehicle solvent, for the glossy finish of concrete, fiberglass and steel surfaces. Excellent mechanical and abrasion resistance Wide range of colors available Uniform gloss finish Low maintenance over time Excellent resistance to UV rays and yellowing Resistant to atmospheric agents Possible non-slip finish Wide range of transparent finishes available Excellent resistance in aggressive atmospheres. Smooth or non-slip finish and coating, resistant to UV rays, water-repellent, with excellent abrasion resistance, for concrete and cementitious supports subject to mechanical stress; smooth finish for fiberglass surfaces, polyurethane insulation and waterproofing systems; colored coating of multilayer systems; colored coating for industrial floors of car parks, ramps, warehouses, etc. o concrete infrastructures such as bridges, viaducts, silos, tanks, pylons, etc.; smooth or non-slip finish and coating, on ceramic, clinker and porcelain stoneware surfaces; Also suitable for steel supports, after appropriate preparation and priming of the support. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating, such as dirt, grease, oil, residues of coatings and surface treatments, etc. The weak parts must be removed before applying the product by mechanical sanding with diamond discs and vacuum cleaning. The tensile strength of the concrete must not be less than 1.5 N/mm². Wet supports In case of residual humidity, apply two or more coats (depending on the irregularities of the support) of Syntech Pavidamp three-component epoxy primer. All cracks in the substrate must be treated and sealed before applying the three-component primer. Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Steel It is necessary to remove solder residues and grind the joints. Sandblasting at Sa 2½ according to ISO8501-1. The surfaces to be coated must be free of dirt, oil, grease and impurities. Average degree of surface roughness RZ ≥ 50 μm. An anti-corrosion treatment is recommended before applying the coating. Ceramic coverings, glass mosaic, porcelain stoneware, clinker Wash the ceramic surfaces to be treated with specific detergents to remove smog, dust, salts, etc. which block the pores to facilitate better capillary penetration of the primer onto the support. Humidity control Before installing resin systems and coatings, always check the residual humidity content. Check for the presence of residual humidity with the plastic sheet method according to the ASTM D 4263 standard: fix a thick polyethylene sheet with a minimum size of 45x45 cm to the support with adhesive tape. 24 hours after installation, lift the sheet and check the presence of traces of humidity. When tested with a carbide hygrometer, the moisture content of the substrate should be < 4% by weight. Primers Concrete The application of SYNTECH PAVICROM PU must always be preceded by the application of a coat of epoxy anchoring primer SYNTECH PRIMER EP-S. Wait 8-12 hours before applying the finish. Resin coatings The application of SYNTECH PAVICROM PU must always be preceded by sanding the entire surface in order to promote and guarantee optimal adhesion of the product to the support. Ceramic surfaces, glass mosaic, porcelain stoneware, clinker The application of SYNTECH PAVICROM PU must always be preceded by the application of a coat of specific primer SYNTECH PRIMER. Wait at least 6-8 hours before applying the finish. Combine the two components in the indicated mixing ratio. Add component B (hardener) to component A (base) and mix well until a completely homogeneous product is obtained. It is advisable to start mixing briefly with an electric drill at low speed and then intensify the stirring up to a maximum of 300-400 rpm. The product can be applied uniformly using a spray gun or short-haired roller to avoid accumulations of material which could give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area to obtain a uniform film and eliminate any accumulations of product. Apply one or more coats of Syntech Pavicrom PU respecting the consumption and thickness indicated. Wait approximately 12 hours, then apply the second coat of colored finish. Approximately 0.15 - 0.20 kg of Syntech Pavicrom PU for each square meter of surface to be coated in two coats. Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B] - Kit: 1 Can 3.3 kg [A] + 1 Can 1.7 kg [B] - Kit: 1 Can 13.4 kg [A] + 1 Can 6.6 kg [B]

I nastri di carta per trasferimento termico sono essenziali per le macchine di misurazione della pelle, offrendo una soluzione versatile e affidabile per le esigenze di stampa. Disponibili in una varietà di colori tra cui bianco, nero, argento, arancione e oro, questi nastri garantiscono una stampa chiara e precisa su tutte le superfici. La loro qualità superiore assicura che ogni stampa sia nitida e durevole, rendendoli ideali per l'uso in ambienti industriali esigenti. Con una gamma completa di dimensioni disponibili, questi nastri si adattano perfettamente a qualsiasi macchina di misurazione della pelle, garantendo una compatibilità senza problemi e una facile installazione. La loro resistenza e affidabilità li rendono una scelta eccellente per le aziende che cercano di ottimizzare i loro processi di misurazione e stampa. Inoltre, l'ampia selezione di colori consente una personalizzazione unica, permettendo alle aziende di distinguersi con stampe vivaci e accattivanti. Scegliendo i nastri di carta per trasferimento termico, le aziende possono migliorare l'efficienza operativa e garantire risultati di alta qualità in ogni progetto.

Le Vernici profumate di DRUCKFARBEN SRL sono disponibili in una vasta gamma di profumazioni, personalizzabili secondo le esigenze del cliente. Queste vernici sono progettate per essere applicate su vari supporti come carta, cartone, plastica, metallo, vetro e tessuto, garantendo il rilascio del profumo anche mesi dopo l'applicazione. Grazie al sistema 'caress & smell', le vernici profumate offrono un'esperienza sensoriale unica, ideale per etichette, carta da regalo, custodie, brochure, inserti, t-shirt, tappetini per mouse, vetro e borse. La nostra azienda offre supporto tecnico completo per l'applicazione delle vernici e l'ottimizzazione dei processi di stampa. Il nostro team è disponibile per fornire consulenza e assistenza in tutte le fasi, dalla scelta della vernice all'implementazione sulle macchine da stampa. Siamo entusiasti di collaborare con voi per offrire soluzioni innovative e profumate per le vostre esigenze. Non esitate a contattarci per ulteriori informazioni o richieste specifiche riguardanti le nostre vernici profumate.

Druckfarben offre una vasta gamma di inchiostri, rivestimenti e adesivi progettati per una varietà di applicazioni industriali. I nostri prodotti sono formulati per garantire una qualità superiore e una lunga durata, rendendoli ideali per l'uso su carta, plastica, metallo e tessuti. Con le nostre soluzioni, puoi ottenere risultati eccezionali in termini di adesione, resistenza e finitura.